In alphabetical order:
The part of a firearm by which it loaded, fired and unloaded.
The process by which metal is softened by exposure to heat. Case necks which have become brittle as a result of repeated resizing can be annealed to prevent cracking and yield longer life. Case neck annealing must be done with care to prevent softening of the case head.
A metallic element which increases the hardness of lead when combined as an alloy.
The part of the primer which offers resistance to the primer compound as the firing pin strikes the primer. In firing, the primer compound is compressed sharply against the anvil and the resulting shearing force sets off the ignition constitutents contained in the primer compound.
A term used by the military to denote bullet. Also used by Olin Industries to describe their spherical powder.
The science and study of projectiles in motion. Divided into three parts: Interior Ballistics is used to describe the events which take place from ignition until the projectile leaves the muzzle. Exterior Ballistics describes the projectile's flight from muzzle to target, and Terminal Ballistics is the study of events after the bullet reaches the target.
The ration of a bullet's sectional density to its coefficient of for, used to describe the bullet's effectiveness in overcoming air resistance during flight.
The gap or space between the cylinder and forcing cone of the barrel in a revolver.
The portion of a projectile which comes in contact with the bore.
The part of the stock which forms the contact with the action and/or barrel. The act of fitting the action to the stock.
A cartridge case with reinforcing belt forward of the extractor groove, characteristic of most modern "magnum" cartridges.
Normally found only in European military cartridges, the Berdan Primer requires a protrusion in the bottom of the primer pocket to serve as an anvil.
The pronounced taper at the heel of a bullet. Used frequently on military and match bullets.
The portion of a case between the head and the point where the shoulder begins to taper.
The part of the action which contains the firing pin assembly, extractor mechanism and the locking system.
The interior of a barrel. When used to describe a rifled barrel, the diameter before the rifling is cut.
The technique of aligning the sights of a rifle with the target by sighting through the barrel.
Today the most common type of primer where the anvil is included in the primer. The case has only one flash hole in the middle of the primer pocket.
A common term used by handloaders in referring to empty cartridge cases. An alloy of copper and zinc.
The cartridge component which, when in flight, becomes a projectile.
The vertical distance of the bullet's trajectory above or below the line of sight.
Tool used to remove the bullet from the case.
A relative term used to define the rate at which a powder burns in comparison with other powders in individual cartridges.
The nominal diameter of the groove or bore, often modified to show the date of adoption (.30-06) or the designer (.257 Roberts), etc. Caliber is expressed either in decimals of an inch (.308") or in metric (7mm) measurements. Rifle or cartridge designations are often merely approximated: for example: .30, .308 and .300 cartridges all use a .308" diameter bullet.
A groove around a bullet that is used for crimping, lubricating or identification.
An early form of today's primer, used to ignite black powder charges. The term is still sometimes used to denote powder.
A complete round of ammunition with all components intact.
The salvageable brass component of a cartridge which serves as a container for the expendable components.
Tool used for trimming case length back to original dimensions.
A cartridge with the primer located in the center of the case head.
The section of the barrel which encloses the cartridge to restrict case expansion during firing.
A molding taken of the chamber by pouring a low-melting-point metal or compund into the chamber. The casting permits accurate measurement of critical chamber dimensions.
The process of reaming or beveling a taper on the inside or outside of a case mouth to remove burrs left by the case trimming operation.
The quantity of powder loaded into a case. Usually expressed in grains and/or tenths of a grain.
An instrument which measures a projectile's velocity electronically, based on the elapsed time between two measured reference points.
The items necessary to load a cartridge (brass, primer, powder, bullet).
A condition where powder is packed more densely in a case than would normally occur. Cause by filling the case to a point where seating a bullet compresses the powder.
The center, lead section(s) of a bullet.
An older type primer in which the compound, if not removed after, attracted moisture and resulted in rust. Use of this compound was generally discontinued about 1950.
To turn the case mouth slightly inward, usually into a cannelure, to grip a bullet firmly.
Tubular shaped smokeless powder which is manufactured by an extrusion process.
To remove the rough and jagged edges left when a case is trimmed to length.
A tool for removing the rough metal burrs from a trimmed case mouth.
To eject the spent primer from the pocket of a fired case.
In reloading, a tool used to re-form a fired brass case or to seat a fresh bullet into the case mouth. In bullet making, a tool used to form the bullet.
Smokeless powder manufactured of nitrocellulose and nitroglycerine.
A term used in exterior ballistics to describe the deviation of a projectile laterally from the Line of Departure. Caused by the projectile's rotation.
The effect of gravity on the projectile. The distance between the line of departure and the trajectory at a given distance.
The vertical adjustment of a sight to bring the of aim into coincidence with the point of impact.
In ballistics, the ammount of work a projectile is capable of accomplishing. Usually measured at the muzzle and as remaining energy at various distances from the muzzle.
The indentations and other marks on the bullet surface caused by the rifling.
The wearing away of the rifling due to hot powder gases and/or bullet friction. The erosion is usually heaviest in the riflings closest to the throat area.
A thicker section of the decapping stem, used to expand the case mouth to the precise diameter required to hold the bullet firmly.
An indication of excessive pressure shown by a ring or "cratering" around the primer indent where the primer has been extruded into the firing pin recess on the bolt face.
Feet per second. The measurement used to describe the velocity of the projectile.
Firing the cartridge to achieve full expansion of the case to the dimension of the chamber.
A spring-loaded, round-tipped pin which is held under compressin after cocking. Pulling the trigger activates a sear which allows the firing pin to snap sharply forward to strike the primer.
Thin, round, flake-type of smokeless powder which is usually of a fast-burning nature.
An opening that provides access through the web for the primer flash to ignite the powder granules in the case interior.
A unit of energy. The force required to lift one pound of weight to a height of one foot.
The forward most portion of the chamber of a rifle. It is located just forward of the chamber neck. The projectile can move without resistance in the freebore and thus the diameter here is allways larger than the groove diameter of the barrel. See also Throat or Leade.
In handloading, the vapor form of burning powder. This heavy gas is capable of expanding rapidly, creating sufficient pressure to propel the bullet.
An alloy of copper and zinc, commonly used for bullet jacket material. Often called Tombac in Europe.
The weight unit used in measuring powder charges or bullet eights. One pound avoirdupois is equal to 7000 grains. 437,5 grains is equivalent to one ounce.
The spiral cut that is removed from the bore to leave the "lands". The grooves of a .30 caliber rifle are approximately .308" in diameter.
A condition where ignition is delayed after the strike of the firing pin.
In reloading, the slight gap that is permitted between the bolt face and the case head to facilitate closure of the bolt. Headspace is actually the distance between the bolt face and the part of the chamber that acts as the cartridge stop.
The distance above the target a shooter must aim when the rifle is zeroed at a lesser range.
A bullet design in which the lead core does not come all the way to the bullet tip.
A highly destructive shock wave created by a bullet passing through any tissue with a high concentration of water such as animal tissue or ballistic gelatin.
The initial combustion of the powder caused by the flame of the primer.
A standard cartridge that has been modified to fit a specially chambered rifle, with less body taper and/or a more sharply angled shoulder. Modification is done by fire-forming in the chamber in which it is intended to be used.
Ballistic tables computed by the late Col. James M Ingalls. The projectiles used by Col. Ingalls serve as the basis for his computations which are regarded as one of the standards for comparison of all small arms projectiles.
The outer covering of a bullet that is used to contain the lead core and improve the "mushrooming" characteristics. Gilding metal is considered best for this purpose.
The keyhole-shaped print of a bullet on the target which indicates it was not stabilized.
The raised portion of the spiral rifling that remains after the groove cuts have been made.
The distance between the mouth of the cartridge and the point at which the rifling engages the bullet. Same as Freebore and Throat.
A projection of the axis of the bore, which is straight to infinity. Line of Departure is coincident with the path of the projectile up to the time the projectile leaves the muzzle.
An imaginary line, straight to infinity, which passes through the sights. Coincident with the point of aim.
The weight of the powder charge, expressed in grains, divided by the volume of the cartridge case, also expressed in grains. The cartridge case volume is obtained by determining the amount of water the case will hold when the bullet is seated to the SAAMI/CIP suggested maximum cartridge length.
Protrusions on the bolt that engage a mating recess inside the receiver ring when the bolt is closed. This feature prevents the bolt from moving rearard when the rifle is fired.
The elapsed time between release of the firing pin and its strike on the primer.
A firearm or cartridge case capable of greater power than is normal for the bullet diameter.
The diameter of the blunt section of a bullet tip.
A primer in which a mercuric compound is used. The corrosive effect of this type of compound has discouraged its use in recent years (see the section of Corrosive Primers).
Metal deposited from the projectile as it passes through the bore.
A calliper-type instrument used to measure thickness or diameter.
A unit of angular measurement equal to 1/60th of a degree. Usually approximated as 1 inch (actually 1.047 inch) at 100 yeards, 2" at 200 yards, etc.
The failur of a cartridge to fire after the strike of a firing pin.
The ideal shape of a bullet following impact against animal tissue.
The end of the barrel where the projectile leaves the bore.
The release of gas from the muzzle immediately, following the projectile's exit.
The energy of a projectile, measured in foot pound, at the muzzle.
The velocity of a projectile, usually measured in fps, at the muzzle.
The narrow portion of the case, forward of the shoulder, which grips the bullet.
A technique used to achieve uniform case wall thickness at the neck by removing metal from the inside of the case mouth.
A resizing technique in which only the neck portion of the case is resized.
A technique to achieve uniform case wall thickness at the neck by removing metal from the outside of the case wall.
A primer containing a priming compound which does not induce rust or corrosion in the bore or case. Most military ammunition prior to 1950 contained a corrosive compound. This pracice was discontinued in 150.
Overall Cartridge Length (O.A.L)
Overall Cartridge Length is as the name indicates, the length of a ready-made cartridge when it consists of a particular selection of components.
The curved, forward portion of a bullet's design.
The unique bullet concept developed by John Nosler, in which a part of the jacket material is used to form a barrier between the front and read lead cores of a bullet. A registered trademark of Nosler, Inc.
A primer that has been punctured, usually by a defective firing pin.
The point where the bullet path intersects the line of sight.
The highly combustible substance that generates a heavy gas upon ignition. The pressure of this gas acts as a propellant to drive the projectile down the bore.
A measuring device designed to throw uniform charges of powder.
A precision measuring device designed for weighing powder; calibrated in grains and tenths of grains.
The force exerted by burning powder. Expressed as "peak pressure".
A small metal cup containing a priming compound which, when crushed against the anvil by the firing pin, creates an intense spark that ignites the powder granules inside the case. Also commonly referred to as a "cap". See also Berdan, Boxer.
A depression in the primer resulting from the strike of the firing pin.
A recess in the head of a centerfire cartridge case which holds the primer.
A bullet when it is in motion after having been fired from a rifle barrel.
A primer that has partially backed out of the primer pocket.
The component of a cartridge which initiates the combustion of the propellant powder that will provide speed and energy to push the projectile out of the gun barrel.
To remove material from a cavity with a rotary cutting tool.
A case with a rim that is of smaller diameter than the case body.
The velocity of a projectile, usually measured in fps, at a given distance from the muzzle.
The residual energy of a projectile, measured in foot pounds/joules, at given distance from the muzzle.
A precisely chambered die used to re-form a fired case to the proper dimensions. When properly used, it will allow the case to be chambered in any rifle of the same caliber.
Paralell spiral grooves, cut into the bore of the firarm, which impart a spin on the projectile.
The flange behind the extractor groove on a cartridge case. Used as a means of extracting a case from the chamber after firing.
A relatively low-velocity cartridge in which the primer compound is located under the rim, inside the case. The firing pin strikes the edge of the case rim, crushing the primer compound and igniting the powder. These cases are not reloadable.
A case with a rim of greater diameter than the case body.
A case with a rim of the same diameter as the case body.
A completely assembled cartridge with all components unused.
A bullet design that features a blunt, spherical shape at the tip.
A split or separation in the case wall or neck.
The depth to which a bullet is inserted into the case mouth.
A die that can be adjusted to control seating depth of a bullet.
The ratio of a bullet's weight, in pounds, to the square of its diameter, in inches.
A case with a rim of slightly larger diameter than the case body.
The cylindrical, straight section of a bullet behind the ogive.
The device that holds the case upright and guides it into the die cavity. A given cartridge requires a shellholder of a specific size.
That portion of a case that sloped from the body to the neck.
Smokeless powder manufactured of nitrocellulose.
The distance between the front and rear sights.
Spherical Powder (Ball® Type)
Smokeless powder shaped into flattened ball granules or round balls.
The rotation of the projectile, caused by the spiral rifling of the bore.
To cause a projectile to rotate rapidly enough around its long axis to keep it from tumbling or yawing in flight.
A process used to form a material under pressure.
The unrifled section of the bore immediately ahead of the chamber. See also Leade and Freebore.
The amount of time it takes for a projectile from the muzzle to the target.
The rate of spiral of the rifling. Given as the barrel length required to make one full revolution: i.e, "One Turn in Ten Inches", etc.
The speed of a projectile in flight. Usually measured in fps or m/s at a specific distance.
A finely graduated, precision measuring instrument of much use to the handloader.
The solid portion of a cartridge case between the bottom of the primer pocket and the case interior. A flash hold through the web provides a means for igniting the powder by the primer.
A cartridge that is not commercially available. Produced from standard cases through the use of special forming dies, the altered case must be fire-formed in the chamber of the rifle to complete the reforming process.
The horizontal adjustment of a sight to bring the point of aim into coincidence with the point of impact.
A lateral change in bullet trajectory caused by crosswind.
In shooting, the point at which the line of sight is coincident with the bullet trajectory at a given distance from the muzzle. In "zeroing" a rifle, sight adjustments are made until this condition exists at the range. Also known as Zero Range or Point Blank Range (PBR).